Malaysia Version XTOOL EZ400 PRO Diagnostic Tool Bluetooth Scanner Free Update Online Support Proton and Perodua DHL Free Shipping

Product Description

③Power Button:  Power on or power off
 

EZ400PRO Technical Parameters
 

Operating System: Android

Processor: Quad-core 1.6GHz Processor

Memory: 1G RAM,16G FLASH

Display: 7.0 inch touch screen with 1024×600 resolution

Sensors: Gravity Sensor,Ambient Light Sensor

Audio Input/Output: Microphone, Dual Speakers, 4-Band 3.5 mm stereo/standard headset jack

Power and Battery: 4000mAh, 3.7V lithium-polymer battery

Power Voltage: 5V

Power Consumption: 8W

Operating Temperature: -20 to 50℃(-4 to 126℉)

Humidity: <90%

Dimension (L*W*H): 218*150*29mm

Tap on EZ400 PRO application, the main interface and sub-menus shows up as below.

XTOOL EZ400 Pro Connection Test
 

 Wired Connection  ①→②→③→④

a. Connect cables and EZ400 PRO in following order: ①→②→③→④

b. Switch on the ignition and turn on EZ400 PRO tablet, then tap on EZ400 PRO application to test vehicles. (Shown as follows)



①
EZ400PRO Mainframe  ② Main Test Cable  ③ OBDⅡ-16  ④ Vehicle

 Precautions Before Use
 

1. The vehicle power supply has to meet the normal voltage limits DC4.8V---5V.

2. When pull and plug test wire harness, users should pinch the front-end of the wire harness to pull and plug, not pull the middle section
    of the wire harness. Users should check the corresponding direction of the port and plug in horizontally when they plug the wire harness,
    instead of inserting in an oblique way, which may damage the terminal.

3. When taking some special functions tests, users are required to operate the device according to operating instructions. For vehicle,
     it has to strictly meet the requirements, for example, the conditions that some vehicle models need to be reached are as follows:
     engine temperature 80℃/105℃,turn  off the loads (such as headlights, air-conditioner, etc.), put accelerator pedal in released position, etc.

4. The ECU for Chinese domestic vehicle models are relatively disorderly, so when users meet conditions, such as the car can not be tested or
     the test data is wrong, they should consider whether the selected menu corresponds to the tested electronic control system, or they can find the
     car ECU and select the right menu according to the model number on the ECU label.

5. If users can not find the tested vehicle model or electronic control system in EZ400PRO test menu, they may need to update the software or
     consult Xtool technical service department

6. Banned to have connection test by using harness not from Xtool to avoid unnecessary losses.  

7. Banned to power off directly in the communication between EZ400PRO and vehicle. Users should cancel the task and return to the main
     interface, then power off.

8. The device should be put and lifted slightly to avoid collision when using EZ400PRO. When click the screen, touch it gently to guarantee
     the service life of the touch screen.

9. During long period of non-use, please disconnect the power and turn it off.

After EZ400PRO tablet connected to vehicle via main cable, diagnosis can be performed now.

The diagnostic interface comes up as below.



Users can choose menu based on their actual needs: 

selection for Europe means entering European cars menu, selection for Asia means entering Asian cars menu, selection for America
means entering American cars menu, selection for China means entering Chinese cars menu. Users also can input vehicle model to search.

 
XTOOL EZ400 Pro Test Functions 
 

Take Volkswagen car for example, select Diagnosis, then select Europe Car, users can see Volkswagen’s logo. If the logo has not been seen,
please swipe up and down or enter the car model to research.

Different vehicles have slight different menus.
 

Common main function menu includes the following options: 

Read ECU
 

This function is to read ECU version information, which is the equivalent of “System Identification” or “System Information” in some
electronic control systems, all mean to read ECU related software and hardware versions, shown as below.

Read DTCs
 

Select Read Trouble Codes to read trouble codes stored in ECU. Screen will show the trouble code and its definition when read the trouble
codes, shown as below.

Tip: In the process of diagnosis, if the device shows “System is OK” or “No Trouble Code”, it means there is no related trouble
code stored in ECU or some troubles are not under the control of ECU, most of these troubles are mechanical system troubles
or executive circuit troubles, it is also possible that signal of the sensor may bias within limits, which can be judged in Live Data.

 

Clear DTCs
 

Return to the previous step, select Clear DTCs to clear current and historical trouble codes memory in ECU. Performing this function
will clear all the current and historical trouble codes. Make sure whether the trouble codes have been recorded before clearing, shown as below.

Click YES to make clear confirmation, if the communication is normal, it will show “Trouble Codes Successfully Cleared” or
“Trouble Codes Cleared”. Generally, users need re-read trouble codes after cleaning them to confirm whether the trouble codes
have been cleared.
 

Read Live Data
 

Auto ECUs send out operating parameters and working status of various components in the form of Electronic Signal, here Electronic Signal
refers to Live Data. Common Engine Live Data includes Engine Speed, Throttle Position Sensor Voltage, Oxygen Sensor Voltage, Coolant
Temperature, Spark Advance Angle, Idle Speed Switch State, Intake Air Temperature, Intake Pressure, etc.


 

Tips: Live Data is the important function for maintenance technicians to further diagnose the troubles. This function needs maintenance
technicians very familiar with sensor data of each system, control signals and control modes, all which are the indispensable basis of using
Live Data function for maintenance technicians.
 

XTOOL EZ400 Pro Display Modes
 

There are two modes to view Live Data, users can choose optimum mode according their own needs and different parameter types.

Dashboard Mode: Display parameters in the form of simulating instrument graphics.

Graph Mode: Display parameters in the form of graph.



 

XTOOL EZ400 Pro Special Functions
 

More special function will be found in different vehicle models. 

Actuatation/Ative/Components Test
 

Test Conditions: Ignition on engine off

If engine started or rotation speed signal recognized, actuating component diagnosing will be interrupted.

In the process of actuating components diagnosis, single component will always be in the trigger status until the next component being activated. 

Before repeating actuating components diagnosis, users should start engine in short-time, or turn ignition off for 2 seconds. 

Actuating components can be checked by hearing or touching.

In the process of all actuating components diagnosis, electric fuel pump is always working.

10 minutes later, actuating components diagnosing is terminated.

Actuating Component: it is responsible for executing various instructions issued by ECU, which is the instruction completer.

 

 Return to Dynamic Diagnostic Data, enter Actuating Components Test and it will show the menu of the actuating components
that carry out action test, shown as below.

Tip: Actuating Components Test performs function tests for parts of system actuating components. When performing this function,
the diagnostic tool will take action test by simulating ECU signal to judge whether the actuating components or circuits are good. 

Return to Dynamic Diagnostic Data, enter Actuating Components Test and it will show the menu of the actuating components that carry out action test.
 

XTOOL EZ400 Pro Settings
 

Select enter Settings; users can set the language, unit and other system related options:

Languages: select the language. Please tick the needed option from multi-language options on the right.



Units: Select unit of measurement. Users can tick Metric or English measurement. 

 

System Settings: Android system setup, such as wireless, audio frequency, light sensation, etc.

Diagnostic Reports
Diagnostic Reports is for checking the saved files, such as the report of Live Data or Trouble Codes or pictures generating in the process of diagnosis, users also can know what cars have been tested. It includes three parts: PDF Files, Pictures and Data Playback.


PDF Files:
PDF files are the diagnostic reports of Live Data or Trouble Codes in the process of diagnosis. Entering PDF can check various diagnostic reports.


Pictures:
Pictures are all the screen capture files in the diagnosis process.
Data Playback:
Data Playback can check what cars have been tested and play recorded Live Data & freeze frame.

Package includes:
 

1pc x OBD II-16

1pc x HONDA-3

1pc x BMW-20

1pc x TOYOTA-17

1pc x MAZDA-17R

1pc x KIA-20

1pc x HYUNDAI/KIA-10

1pc x NISSAN-14

1pc x GM/DAEWOO-12

1pc x SELFTEST

1pc x UNIVERSAL-3

1pc x SUZUKI-3

1pc x FIAT-3

1pc x CITROEN-2

1pc x AUDI-4

1pc x MITSUBISHI-12+16

1pc x BENZ-38

1pc x BENZ-14

1pc x MAINCABLE

1pc x Battery Cable

1pc x Cigar Lighter Cable

1pc x EZ400PRO Tablet

1pc x Charger for Tablet

1pc x Charger US Adapter 

1pc x Charger EU Adapter

1pc x MicroUSB Cable

1pc x Tool Case

1pc x Certificate of Quality

1pc x Packing List

1pc x User Manual

1pc x Carton
 

Shipping Warranty 
If you have no special requirements, we automatically select the shipping warehouse and shipping method for you by default.

US, UK,EU Warehouse Shipping: 
2-5 working days. We have stocked up hot sale items in US,UK,EU Warehouse , which is more convenient for customers. Free TAX, faster shipping with cheaper price. Orders from US,UK or EU will be delivered by US Fedex/USPS,DE DHL Post or Royalmail Hermes,DPD from US,EU, UK warehouse.

DHL Shipping: 3-7 working days, To help you clearance we will help declare a lower price on the invoice to help clearance. If address is remote area, you need pay remote freight or we will ship by Normal Post or Yanwen/EMS/Aramex Express.Please remember to leave message if you have any special requirement.

Yanwen Express: 7-15 working days, usually No Tax for European Countries or Remote Area . The tax was pre-paid, when package reached, there's no tax no extra fee for customers.Due to high custom tax in European Countries,Like United Kingdom, Germany, France, Italy, Spain, Belgium,Austria, Portugal, Hungary,etc, we will use Yanwen express or DHL.
(Default ship via DHL,if you need other shipment method , please inform us first. thank you)

Postal Service: 12-20 working days,although takes long time but also free tax

Product Warranty

All the XTOOL tools in our site we provide one year warranty. 

Technical Service  

1. If you have any technical problem, please contact us online or by email sales@Xtooleshop.com
2. Remote help service: If your problem needs to be solved by remote help by our engineer, please download the teamviewer software, install it on your computer, then give us ID and password for remote help.

 Refund policy 

1. Damaged tool Service: If the product you received has been damaged during the shipping, please report to local DHL office/Post office immediately and ask for damage proof, then contact our website customer service for exchange service.
2. Product Quality problem for refund or exchange: If the product has any problems, please contact our customer service online within 7 days and return the item to us within 30 days upon the arrival.If you not contact us within 7 days and not return to us within 30days, it is considered as used and WE WILL NOT ISSUE YOU A REFUND OR REPLACEMENT.
3. Return Service: All returned items MUST BE in the original packaging and you need to provide us with the shipping tracking number, specific reason for the return, and also your order number. Buyer pays return shipping fee.

Join our community: